Stainless and plated brass with hard enamel, laser engraving and reverse personalisation. Plating thickness stated in microns, spring specification included, and the die held so a reorder never pays tooling twice.
WhatsApp Us Contact UsThe function is to hold tie to the shirt placket so it stays centred and does not swing forward when the wearer leans over. That is genuinely useful for anybody who eats lunch in a tie, works at a counter, or bends over a desk repeatedly.
It follows that a tie clip must grip both the tie and the shirt. A clip attached to the tie alone does nothing except decorate it, and it is the most common mistake we see. If the shirt is not inside jaws, the clip is jewellery.
That single point is worth including in any uniform briefing, because it costs nothing and it visibly improves how a team looks.
Three conventions govern this, and getting them right is free.
Height. Between the third and fourth button of the shirt, which places it at roughly midpoint of the chest. Too high looks fussy. Too low looks like wearer is trying to hold down a tie that is too long, which usually they are.
Width. The clip should be narrower than the tie, ideally covering around three quarters of its width. A clip wider than the tie looks wrong immediately and is the most visible error. Standard clips run 45 to 55 millimetres, which suits most modern ties. Slim ties at 5 to 6 centimetres need a clip nearer 40 millimetres.
Angle. Horizontal. Angled clips are a style choice that reads as trying too hard in most professional settings.
For uniform programmes, supplying a short card with the clip showing correct placement costs almost nothing and it materially improves consistency across a team. We produce alongside clips when a client want them.
A tie clip works as a corporate gift for a specific reason. It is used, it is seen, and it is not something most people buy for themselves.
For senior client gifting, hard enamel or engraved stainless in a presentation box reads as considered. Restraint works better than prominent branding, since a recipient is more likely to wear something that does not advertise a supplier across their chest.
Long service awards suit format well, particularly with a discreet year or milestone engraved on the reverse where only wearer knows it is there.
Sets pairing a tie clip with cufflink in a fitted box are the traditional arrangement and remain effective. Producing both together guarantees finish matches, which sourcing separately rarely achieves.
Consider recipient list. Formal business dress is standard across much of the professional sector here, and a tie clip suit that audience well. For a mixed recipient list it is worth pairing with an alternative item so the gift is appropriate across the group.
Groomsmen gifts are a steady part of this category. Matching tie clips for the wedding party, frequently engraved with initials or the date, and often coordinated with the ties themselves.
Quantities are small, expectations on finish are high, and the deadline is immovable. We build contingency into any wedding schedule rather than quoting theoretical minimum, because a delay that would be an inconvenience elsewhere is a genuine problem here.
Presentation matters disproportionately. A tie clip in a fitted box with a printed card reads as a gift. The same clip in a poly bag does not.
Membership pins, achievement markers and honour society insignia all use the same manufacturing. Hard enamel with plated finishes is the usual specification because these are intended to be kept indefinitely.
Where a scheme runs annually, holding tooling and the specification means each year's batch matches last, which for an award worn alongside previous recipients matters.
Minimum order is around a dozen for laser engraved stainless, and higher for enamel work because a die must be produced. Enamel minimums typically start around a hundred pieces.
Cost is driven by material, plating specification, decoration method, whether pieces carry individual text, packaging, and quantity. The die for enamel work is a one time charge held on record for reorders.
Lead time is one to two weeks for engraved stainless, three to four weeks for enamel work including die production, and longer for precious metals or complex multi part construction.
Rush production is possible on engraved work and is genuinely constrained on enamel, because plating and curing stages cannot be compressed.
What is the base metal? Stainless and plated brass behave differently over years.
What is the plating thickness? Almost never quoted and it decides whether finish survives. Ask in microns.
Soft or hard enamel? Hard is polished flat, more durable and more expensive. Both are legitimate and they should not be priced as though equivalent.
What grade of spring? A weak spring lets clip slide down tie, which is the most common in service complaint.
Is the die charge one time? It should be, and it should stay on file for reorders.
Is packaging included? On a gifting order this is a significant proportion of the perceived value and is frequently quoted separately.
Clip wider than the tie. The most visible error and the easiest to avoid. Specify width against ties actually being worn.
Not clipping to the shirt. Half workforce will do this unless told otherwise, and the clip then serves no purpose.
Thin plating on a uniform item. It wears through at the pinch point within months and looks worse than plain steel.
Weak springs. The clip slides down tie through the day and is eventually lost.
Epoxy dome for a premium gift. It reads as promotional however good artwork.
Ordering exactly headcount. Uniform items are lost continuously and new staff join. Build in a margin and a replacement route.
Metal accessories score reasonably well here, mainly through durability. A properly specified tie clip lasts years and is fully recyclable at the end of its life.
Plating is the weaker element, since the process involves chemistry that requires proper handling, and thin plating shortens item's life considerably. Specifying adequate plating thickness is both a quality and an environmental decision.
Epoxy dome and plastic inlays complicate recycling and are the least durable option, so they are the weakest choice on both counts.
For gifting programmes, the most useful discipline is ordering what will genuinely be given rather than a comfortable overage, since surplus branded accessories sit in cupboards indefinitely.
An accessory programme succeed or fails on coherence, and tie clips are usually specified last when the ties, shirts and badges are already decided.
Metal finish should be consistent across every metal item a member of staff wear. If the name badge is silver and the tie clip is gold, the effect is noticeable even to people who cannot say why something looks assembled rather than designed. Belt buckles, lapel pins, badge holders and cufflinks all belong in the same conversation.
Tie width is the practical constraint and it is the one most often overlooked. Corporate tie widths here range from around 6 to 9 centimetres depending on how recently uniform was designed, and the clip has to be narrower than whatever is actually being worn. Measuring an existing tie before ordering takes a minute and prevent a whole batch being wrong.
Where an organisation is refreshing ties and tie clips together, specify both at once so the proportion is correct by design rather than by luck.
Shirt fabric matters slightly. A heavier oxford weave gives a pinch clasp more to grip than a fine poplin, and on very lightweight shirts a stronger spring or a chain style is worth considering.
For organisations with several uniform tiers, front of house, management and back of house, deciding which tiers wear tie clips at all is worth settling explicitly. Issuing them to staff whose role makes them impractical simply produces items in drawers.
On an item this small, presentation carries a large share of the perceived value.
For uniform issue, bulk packing in labelled bags by department is efficient and appropriate. Nobody expects presentation on a workwear item.
For gifting, a fitted rigid box with a foam or card insert is the minimum that reads as a gift. A printed sleeve around it adds branding without cluttering box itself.
For sets pairing tie clips with cufflinks, a fitted insert holding both pieces in position turns two items into a considered set rather than two things in a box.
Velvet and suede pouches are a lower cost alternative that still reads as premium, and they suit wedding party gifts particularly well.
For retail, a header card with a punched hole allow hanging display, and it gives space for the material and finish information a buyer want before purchasing.
Because we produce packaging in the same building, boxes, inserts and cards carry matched branding rather than being sourced separately and approximately aligned.
Uniform programmes reorder continuously as staff join and items are lost, and the value of a supplier is largely in whether batch twelve matches batch one.
We hold base metal, the plating type and thickness, the enamel colour codes, the die reference, the dimensions and the spring specification indefinitely at no charge. A replacement order become a quantity and a date.
The die for enamel work stays on our records so a repeat run carrie no fresh tooling charge, which is the largest single cost on a first order and should never be paid twice.
For larger operations we recommend producing an annual quantity in one run and releasing against a schedule, which secures volume price, guarantees every piece comes from one plating batch, and avoids urgent small reorders at poor unit rates when a department runs short.
Where a design is being retired, we flag remaining stock rather than letting an organisation discover it holds several hundred tie clips carrying a superseded logo.
Send quantity, whether pieces are for uniform or gifting, the finish you have in mind, the width of the ties being worn and the date you need delivery.
If you have artwork we check it at no charge and tell you honestly whether it reproduces at the size involved. A logo designed for a letterhead frequently needs simplifying for a fifty millimetre bar, and hearing that at the start prevents a redesign after tooling has been made.
For enamel work, tell us brand colour references and we produce a physical sample against them rather than approximating from a screen.
For uniform rollouts, tell us total headcount plus expected joiner rate, and we will advise on quantity including a sensible allowance rather than quoting exactly what was asked for and leaving you short in three months.
Most quotes go out same working day, and we produce a physical sample before any substantial run because plating and enamel are two things a specification sheet describe poorly.
This is a small item where the specifications that matter are invisible on delivery and decisive after a year of daily wear, which makes it very easy to buy badly.
We state plating thickness in microns rather than describing a finish as durable. We specify hard or soft enamel explicitly rather than letting ambiguity sit in the quote. We use proper spring steel, because a clip that slide down tie is the complaint we hear most about other suppliers. We hold die so a reorder never pays tooling twice. And we record plating batch so a replacement set matche one already in service.
We also give advice that reduces order. Telling a client their tie clip are wider than their ties. Suggesting branding goes on the reverse so recipients will actually wear piece. Recommending stainless over a plated finish for a security team who will destroy plating within months. None of it is what somebody wants to hear when they have already chosen, and all of it produces something that works.
A tie clip is worn at chest height in every meeting wearer attends. Over a year that is a very large number of impressions from a very small object, and it is worth specifying properly rather than cheaply.
We deliver to Dubai, Abu Dhabi, Sharjah, Ajman, Ras Al Khaimah, Fujairah and Umm Al Quwain.
Uniform rollouts are packed and labelled by department, location or shift so distribution is a matter of handing out sealed bags rather than counting on the day. For organisations issuing against a register, we can supply numbered pieces with a matching list.
Gifting orders arrive individually boxed and, where names are involved, labelled per recipient so handover is straightforward.
For programmes running continuously we hold stock and release against agreed trigger levels, so a department never runs short and never places an urgent small order at a poor rate.
Very little is needed and the wrong attention causes most of the damage we see on returned pieces.
Wipe with a soft dry cloth. Plated finishes need nothing more, and polishing compounds designed for solid metal will strip plating rather than clean it, which is the most common way a good finish is ruined.
Keep them dry. Perfume, aftershave and hand sanitiser all attack plating, and applying scent before putting on tie clips rather than after makes a measurable difference over years.
Store them somewhere they cannot rub against other metal. A small pouch or a compartment in a tray prevent scratching that dulls a brushed finish.
Sterling silver tarnishes and responds well to a proper silver cloth. Rhodium plated pieces do not tarnish at all and need no such treatment.
For uniform programmes, a line about care on the issue card costs nothing and extends replacement cycle noticeably across a large workforce. Most premature wear we see comes from well intentioned polishing rather than from use.
Custom neck ties are ordered alongside clips for uniformed teams, and woven rather than printed silk holds a fine pattern at the small scale a tie needs.
Custom cufflinks are produced in the same materials and finishes as tie clips, and the two are frequently ordered as a boxed pair for gifting. Cufflinks Dubai clients order for weddings and corporate recognition are usually engraved or enamelled with initials, a date or a company mark.
Mens ties Dubai companies order for uniform are woven rather than printed, so the pattern sits in the fabric and cannot crack. Pre tied ties suit school and service uniforms where a consistent knot matter more than individual tying.
