How tall, how heavy and how bright: a practical guide to specifying a letter standing display for an office lobby, with materials, prices and a stability rule.
Freestanding letters in a lobby look simple: big letters, on the floor, spelling the company name. Then someone leans a laptop bag against the A, a cleaner's trolley clips the corner of the R, and the facilities manager asks why one letter is 20 mm shorter than the rest. A letter standing display is a piece of light engineering as much as a sign, and getting it right comes down to four numbers: letter height, letter depth, base weight and light output. We fabricate these in our Ajman workshop for offices from DIFC to Al Reem, and this guide gives you the numbers before you ask for a quote.
Letter height by viewing distance
Start a letter standing display with where it will be read from, not with how big the lobby is. The rule we use is 25 mm of letter height for every metre of viewing distance, then round up to the nearest standard size.
| Where it stands | Typical viewing distance | Letter height | Letter depth |
|---|---|---|---|
| Reception desk front, read from the door | 6 to 8 m | 200 to 300 mm | 50 mm |
| Lobby floor, read from the lift | 10 to 15 m | 400 to 600 mm | 80 to 100 mm |
| Atrium or double height entrance | 20 m plus | 800 to 1,200 mm | 120 to 150 mm |
| Event stage or photo spot | 3 to 5 m, photographed | 600 to 900 mm | 100 mm |
Depth matters as much as height for 3D letters. A 600 mm letter that is only 30 mm deep looks like a cut out and will not stand on its own. At 80 to 100 mm deep the letter reads as an object, casts a shadow and gets a base wide enough to be stable. Our acrylic and channel letters are built at these depths as standard.
The base weight rule
This is the part most quotes skip. A letter standing display must survive a child pulling on it and an adult tripping into it. Our rule: the total weight at the base should be at least 1.5 times the weight of the letter above it, and the base footprint should be at least 60 percent of the letter height from front to back. Acrylic letters at 600 mm weigh about 4 kg each and sit on a hidden steel plate of 6 kg or more, 360 mm deep, concealed inside the bottom stroke of the letter or inside a slim plinth that runs under the whole word.
Round freestanding letters, O, C, G and S, are the troublemakers, because they touch the floor at one point. We fit them with a flat internal foot or link the whole word on a common base rail. For letters over 800 mm, the rail is the only safe option, and it also keeps the baseline dead straight, which is the detail people notice without knowing why.
Materials by budget and look
Acrylic, solid or built up. Acrylic letters are the most common letter standing display material. Solid cast letters up to 300 mm are cut from 20 to 30 mm sheet and polished; above that, letters are built up from a face, a back and sides, which keeps weight down. Opal white, brand colours or a mirror finish. AED 180 to 450 per letter at 400 mm, depending on depth and colour. This is the default for a modern office lobby and the easiest material to light.
Stainless steel or aluminium. Fabricated metal 3D letters with a brushed, mirror or powder coated face. Heavier, so the base can be smaller, and they take knocks far better than acrylic. AED 350 to 800 per letter at 400 mm. Right for law firms, banks and anyone whose brand palette is metal.
Foam core with hard coat. For event use and temporary installs, 100 mm thick high density foam letters with a sprayed hard shell weigh a fraction of acrylic and cost AED 90 to 200 per letter at 600 mm. They are made the same way as our foam board cut outs and are the right material when the letters travel between events.

Timber. Oak or walnut veneered 3D letters for hospitality and wellness brands. Warm, heavy, and best kept away from direct sun through facade glass.
Need acrylic letters priced for your quantity?
Lighting a letter standing display
Illuminated letters change a lobby after dark and in photos, which is why most requests for a letter standing display now include light. There are three ways to do it, and each changes the build.
- Face lit. Opal acrylic face with LED modules inside. The letter glows as a shape. Brightest of the illuminated letters and the one to pick for a dim lobby.
- Halo lit. Solid face, open or opal back, so the illuminated letters spill light onto the floor around each character. Subtle and architectural, excellent on stone floors.
- Edge lit. Clear acrylic with light fed in from the base so the letter outline glows. Delicate and best at smaller sizes, and the same technique we use on desk name plates.
Power is the practical constraint. Freestanding letters cannot have a cable snaking across the floor, so either the word sits against a wall with a socket behind it, or a floor box is installed where the base rail will sit, or the letters run on a rechargeable battery pack hidden in the plinth, which gives about ten hours and suits event use. Decide this before the floor is finished, because a floor box after the fact costs more than the letters. For a bulb style, retro effect, the marquee board letters use exposed LED lamps and work well in cafes and co working spaces. Where the brand wants colour change, a neon style LED flex from our neon signs range can be set into the letter face.

Floor protection and placement
Marble and porcelain lobbies scratch under a letter standing display. Every base we supply has a 3 mm felt or rubber pad, and for letters over 20 kg a load spreading plate so point loads do not crack a tile. Place the word where it is seen from the entrance but not in the walking line between the door and the lift, usually to one side of the reception signage or as the front face of the desk itself. Leave 600 mm clear in front for photographs; a letter standing display in a Dubai office doubles as the photo spot for new joiners and visiting clients within a week of going in.

Keep the letters 200 mm away from facade glass. Afternoon sun through glass heats acrylic letters unevenly and can warp a built up letter over a summer, and the glare behind the letters kills the photo.
Prices for a typical word
An eight letter company name as a letter standing display in 400 mm built up acrylic, opal white, face lit, on a common steel base rail with felt pads and a battery pack, comes to AED 4,800 to 7,200 installed in Dubai, Sharjah or Ajman. The same word unlit, on individual hidden bases, is AED 2,400 to 3,800. In brushed stainless, unlit, AED 4,000 to 6,500. Foam letters at 600 mm for an event, AED 1,200 to 1,800 for the set, and a matching cutout standee of the logo mark is AED 350 to 600. A metal sign board behind the letters, carrying the strapline, is a common addition at AED 800 to 1,500.
Ordering a letter standing display from us
Send a photo of the lobby from the door, the word or logo as a vector file, the floor material and whether there is a socket or floor box nearby. We reply on WhatsApp with a letter height, a base design and a quote. Fabrication is eight to twelve working days for acrylic and metal, four for foam, and we install across all seven emirates with our own fitters. For the exterior version of the same idea, see our facade signage. For the wall mounted sizing rules that complement this guide, the signage overview covers the full indoor and outdoor range.
Specify the four numbers, height, depth, base weight and light, and the letters will still be standing straight when the lease ends.
Ready to get started?
Look, we have been in this business long enough to know what works and what doesn't. If you are not sure where to begin, just give us a call. No pressure, no sales pitch. We will walk you through the options and give you an honest quote.
What you get with us:
- Straight answers about what you actually need (not what costs most)
- Fair pricing. We will tell you how to save money where it makes sense
- Quick turnaround when you need it, or save by planning ahead
Need Acrylic Letters in the UAE?
Our team produces acrylic letters and related print for businesses across Dubai, Abu Dhabi, Sharjah and every emirate. Send us your brief for a same day quote.
Get Your Free Quote+971 56 978 6395
Atiya Naaz
Marketing Head, Branding Blitz
Atiya brings five years of hands on experience in the UAE printing and branding industry. Based in Abu Dhabi, she leads marketing team at Branding Blitz, helping businesses across Dubai, Abu Dhabi, Sharjah, and all emirates find right print solutions for their branding needs. Her expertise spans corporate identity materials, exhibition printing, packaging design, and digital marketing strategy for the regional market.
Related resources: See our desk accessories, marketing materials and event props pages for specifications, quantity pricing and design options across the UAE.


